Changed the name of GSE tech-motive tool to CP Techmotive. CS4000 Controller Technical Reference Manual (part number 1). Feb 23, 2012 - DK-4000 Roskilde, Denmark [email protected]. User's Manual for BECAS v2.0 - a cross section analysis tool for anisotropic and. Boyan Lazarov (Department of Mechanical Engineering, Technical University. Fact the underlying motivation for the use of constraint equations as described in. ![]() ![]() • CS-400 01-40D-00 SERVICE MANUAL SUPPLEMENT CHAIN SAW CS-400 ECHO: (Serial number: 1109999) (Serial number: 1209999) (Serial number: 1309999) INTRODUCTION CONTENTS page We are constantly working on technical im- 1 SERVICE INFORMATION.2 provement of our products. For this reason, 1-1 Specification. • CS4000 Mini Controller with Ethernet Technical Reference Manual. • 24-Hour Technical Support Toll Free: 1-877-224-7377 ® SPX GSE tech-motive tool manufactures products under the GSE and tech-motive tool brand names. • Please Note: has a new name. We are now This change of name is not yet reflected in the documentation for this product where you will still find the old logo and company name. The new address is: SPX GSE tech-motive tool 42860 Nine Mile Road, Novi MI The toll free service number remains the same: 1-877-224-7377. • LIMITED WARRANTY Except for perishable items, such as the fuses and batteries, SPX GSE tech-motive tool warrants its GSE tech-motive tool brand fastening products, GSE brand sensors and instruments, and fastening systems to be free from defects in materials and workmanship for one year from the date of shipment from the manufacturing facility. • Acknowledgments Special thanks are extended to the following SPX GSE tech-motive tool management, software and hardware engineers who provided value information in the development and review of this manual. Jim Grenier Tom Jozwiak Ken Lehoczky Larry Piggins Rick Szwast Steve Urbanski Bill Welch Karen R. • This Preface provides conventions and abbreviations used throughout this manual. If you have never used a CS4000 Mini Controller with Ethernet, read this manual entirely. The first three chapters will help you become familiar with safety requirements, the location of components, software and features. • CS4000 Mini Controller with Ethernet If you want to use the CS4000 Mini Controller with Ethernet with a network or laptop computer, refer to Chapter 5. Setting Up the Ethernet, Chapter 6. Setting Up the 485 Network and Chapter 7. Setting Up the RS-232 Link that describe the methods by which you can connect the CS4000 Mini Controller to a network or laptop computer. • Preface Abbreviations Some of the most common abbreviations used throughout this manual include the following: Application Program Interface GFCI Ground Fault Circuit Interrupter Input/Output IEEE Institute of Electrical and Electronic Engineers Internet Protocol kbps kilo-bits per second kilovolt-ampere Local Area Network Light Emitting Diode mbps million bits per second. • CS4000 Mini Controller with Ethernet (This page is left blank intentionally.) Page T-38324-A 4. • Using a 485 Network using SDLC..1-4 Example of a “Permanent” (Embedded) 485 Network.1-5 (Using CS4000 KDM and Mini Controllers with SDLC)..1-5 Using the RS-232 Serial Port..1-6 Using an Interbus-S Digital I/O Module..1-6 Using the Siemens 3964R Barcode Protocol.. • Interbus-S Module...3-16 Ground Fault Circuit Interrupter..3-18 Fuses...3-18 4. Installing the CS4000 Mini Controller with Ethernet..4-1 Mounting the CS4000 Mini Controller with Ethernet.4-1 Power and Connection-Requirements.. 4-3 Meeting the AC Input Power Requirements.. 4-4 Grounding... • Contents 7. Setting Up the RS-232 Link...7-1 Setting Up Visual Supervisor..7-1 Using RS-232 Cables...7-1 8. Maintenance/Troubleshooting..8-1 Replacement Parts... 8-1 Replacing Main Power Fuses..8-2 Replacing Backplane Fuses..8-2 Cleaning the Enclosure Window... 8-2 Troubleshooting... • Figure 3-2. Top Panel View...3-3 Figure 3-3. Bottom Panel View...3-4 Figure 3-4. Components Inside the Enclosure of the CS4000 Mini Controller with Ethernet...3-7 Figure 3-5. Front View of the TCM...3-8 Figure 3-6. Rear View of the TCM and Location of the Servo Amplifier Fuse.3-9 Figure 3-7. • Figure 9-1. CS4000 Mini Controller with Ethernet Wiring of Standard Ethernet and Interbus-S Module... 9-3 Figure 9-2. CS4000 Mini Controller with Ethernet Wiring of Standard Ethernet.9-5 Tables Table 3-1. Description of Ethernet Interface Card LEDs..3-15 Table 3-2. • CS4000 Mini Controller with Ethernet (This page is left blank intentionally.) Page T-38324-A 4. • You simply plug in the tool, power up the system, program the desired tightening parameters and begin production. A complete fastening system is made up of the CS4000 Mini Controller (with or without) Ethernet, a tech-motive tool nutrunner (46, 66 or 116 Series) and a standard tech-motive tool cable. The CS4000 Mini Controller with Ethernet houses one Tool Control Module (TCM), with fuses and ground fault circuit interrupt (GFCI) protection. • 4.06 or higher installed on the controllers. The CS4000 Mini Controller with Ethernet also has an optional Application Program Interface (API) which you can have built into each controller.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |